MerCruiser Electronic Control Module ECM 2001 2006 5 0 5 7 6 2

Thursday, January 8, 2015

The following information covers factory service procedures for electronic control module (or ECM) on MerCruiser inboard engines. Procedures applicable to the 5.0L/5.7L/6.2L MPI gasoline engines for 2001 2002 2003 2004 2005 and 2006 models. 



STERNDRIVE MCM
  • 5.0L V8 MPI Alpha and Bravo
  • 350 MAG MPI Alpha and Bravo
  • 350 Mag MPI Alpha and Bravo Horizon
  • MX 6.2L MPI
  • MX 6.2L MPI Horizon
INBOARD AND TOW SPORTS (MIE)
  • 350 V8 5.7L MAG MPI Inboard
  • 350 V8 MAG MPI Horizon Inboard
  • MX 6.2 Multi-Port Injection Inboard
  • MX 6.2 MPI Horizon Inboard
  • 350 MAG MPI Tow Sports
Testing and diagnosis helps determine problems and possible causes. Its important to perform extensive testing and troubleshooting prior to any major tear down or repair work. This ensures that the full extent of the problem is understood beforehand and may prevent any unnecessary repair work. Its recommended you use a factory repair manual when performing repairs on any vehicle, additional safety precautions, or technical data maybe included. 

ECM REMOVAL

IMPORTANT: The ECM is a very sensitive piece of electrical equipment and is subject to electrostatic damage. Never touch the connector pins when installing or removing the electronic control module. 

1. Detach the electrical connectors on the ECM. Never touch the connector pins. 

2. Take off the ECM from the module bracket.

ECM CLEANING AND INSPECTION

1. Clean the outer exterior of the ECM with a dry and clean shop towel. Do not touch the touch or come in contact with the connector pins.

2. Check the outer housing for signs of excessive wear, corrosion or damage.

3. Carefully inspect the electrical pins at both ends of the ECM for corrosion and straightness.

4. Carefully inspect the wiring harness connectors for signs of corrosion and terminals for loose connections.

NOTE: The ECM is a designed to be a sealed electrical device, if the item appears to be damaged, replace the ECM.

ECM INSTALLATION

1. Install the ECM back on the module bracket using the existing washers and brackets.


2. Reconnect the ECM wiring harness connectors, never touch the connector pins. 

ECM MerCruiser
  • 2002 5.0 l mercruiser ecm
  • 2002 6.2l mercruiser engine ecm connect
  • 2002 mercruiser 350 mpi ecm
  • 2003 harley ecm overheating
  • 2003 mercruiser 350 mag, wiring harness, ecm
  • 2004 mercruiser 5.7 mag mpi ecm
  • 2007 mercruiser 350 mag mpi horizon inboard ecm module
  • 350 mag mercruiser ecm alpha
  • 5.0l ecm mercruiser buy
  • 5.7l mercruiser ecm battery fuse
  • 6.2 mercruiser ecm programming
  • how to replce ecm in mercruiser thunderbolt
  • how to test mercrusier 6.2l ecm
  • merc cruiser ecm modual testing
  • mercruiser 350 ecm different bravo/alpha?
  • mercruiser 350 ecm electrical repair manual torrent
  • mercruiser horizon engine ecm
  • mercruiser mx 6.2 mpi horizon ecm connector
  • rebuilt ecm for 6.2 mercruiser problems
  • reflash ecm on mercruiser mx 6.2 mpi
  • removed the ecm on a 350 mercruiser
  • used mercruiser ecm engine control module 350 mag mpi
  • where is the ecm plug in a 2007 6.2 mie

Related Posts by Categories

0 comments:

Post a Comment